Home

Help

Testimonials

New Arrivals

View Cart

Install Tips

Categories

Bestsellers

1. Mitsubishi OEM Turbo Gasket - EVO 8/9/X
2. Mitsubishi OEM Turbo to Exhaust Manifold Bolt Kit - Evo 8/9
3. Mitsubishi OEM Manifold-Turbine Stud - Evo 8/9
4. Mitsubishi OEM Turbo Nut - EVO 8/9/X
5. Mitsubishi OEM Turbo Oil Return Tube - Evo 8/9
6. Mitsubishi OEM Turbocharger Compressor Outlet Gasket - EVO 8/9/X
7. Mitsubishi OEM Turbine-02 Stud - Evo 8/9
8. Mitsubishi OEM Turbocharger Oil Line Gasket
9. Mitsubishi OEM Turbo Oil Feed Tube - EVO X
10. Mitsubishi OEM Turbo Water Feed Pipe - Evo 8/9

Testimonials

I was looking to complete the last stage of Evo mods I had planned for this year, so after comparing prices from other sites, I landed on Lancer Shop because they seemed pretty consistently fair and knowledgeable.

After getting everything I needed, I went to go checkout and my credit card bombed - three times. It was disappointing for sure, and figured I'd have to wait a pretty long while before I could resubmit my order, and hopefully hadn't accidentally charged my card three times.

Thankfully, Janelle contacted me via e-mail, and was extremely patient and helpful getting my payment mess resolved. We switched up cards, tried again, and it went through perfectly. She deserves some serious kudos. I've dealt with service people before who either couldn't be bothered or caved under the pressure of a crazy customer screw-up, but she handled it quite well.

I will definitely be returning in the future for more accessories and parts!

Camdon

View All Testimonials

Write Your Own Testimonial

AGP Front Mount Intercooler: EVO X

Product Description

AGP Front Mount Intercooler: EVO X

Part # AGP-EVOX-FMIC

Fits: Lancer EVO X 2008+

Enhance the performane of your 2008-up Mitsubishi Evolution X with the first front mount intercooler available, and now with cast end tanks! The AGP Turbo FMIC features cast aluminum end tanks attached to a 20"x13"x3.5" bar and plate core. This core has the largest surface area of any other core on the market. This assembly fits perfectly in the factory location and does NOT require you to remove or trim any portion of the stock bumper support. It also clears the factory lower under-tray so you do not need to remove it. It cools at 90-99% efficiency under almost all conditions and has less than .75psi pressure drop at 450 hp of airflow. You couldn't heat soak this intercooler if you tried.

Stop asking who manufactures our core for us. We're tired of explaining it, and we're not going to tell you. All you need to be concerned with is that you're getting the best intercooler for your Evo X. Look up reviews, look up dyno numbers, look up track times. Our intercooler steps it up and delivers.

Throughout our dyno testing on the Evo X, we kept seeing timing retard (knock) around 5000rpm with the factory intercooler and 91 octane gas, where the power would drop. Since we upgraded to this intercooler, we've noticed consistent power across the board due to a cooler air charge. Back to back pulls on the dyno now result in identical power curves due to no heatsoak. This is a great upgrade for a stock Evo X, and will help you make more and more power down the road as we continue to release products.

Dyno results showed peak gains of 20 ft/lbs and 25 whp, and nowhere did it lose power throughout the entrire RPM range. These tests were done on a car with a stock turbo, minor bolt ons, and a very conservative ECUTEK tune.

This is the same intercooler we run on our shop car, which so far has made over 530whp and trapped 11.55 @ 123.

The FMIC includes:

20"x13"x3.5" bar and plate core with cast end tanks weighing in at 24.5 lbs.
Silicone hoses and clamps
All necessary installation hardware
**2010 models will require a new mounting bracket as Mitsubishi decided to change the lower intercooler mount. $25**

Available with a black heat dispersion coating that helps "pull" the heat from the intercooler core- aiding with thermal transfer and increasing intercooler efficiency.

Available with the AGP logo stencil that will allow you to paint our logo on the intercooler any color you like. We recommend using brake caliper paint, it seems to hold up the longest.

Details

Price: $731.95

Purchase Product



Logo Stencil:
2010+ Model:
Heat Dispersion Coating:

Qty

If you see this message, your web browser doesn't support JavaScript or JavaScript is disabled. Please enable JavaScript in your browser settings so the online store can function correctly.