Home

Help

Testimonials

New Arrivals

View Cart

Install Tips

Categories

Bestsellers

1. WORKS High-Flow Service Kit
2. OEM Mitsubishi Drip Moulding Clip - EVO 8/9
3. Mitsubishi OEM Maintenance Manual - EVO 8
4. MITSUBISHI EVO 8/9/X TRANSMISSION FLUID OEM DIAQUEEN QUART MZ320197
5. Tire Garage
6. Mitsubishi OEM Fuel Filter Kit 1770A270 - Mitsubishi OEM Lancer
7. Mitsubishi MR245062 EMBLEM

Testimonials

I was looking to complete the last stage of Evo mods I had planned for this year, so after comparing prices from other sites, I landed on Lancer Shop because they seemed pretty consistently fair and knowledgeable.

After getting everything I needed, I went to go checkout and my credit card bombed - three times. It was disappointing for sure, and figured I'd have to wait a pretty long while before I could resubmit my order, and hopefully hadn't accidentally charged my card three times.

Thankfully, Janelle contacted me via e-mail, and was extremely patient and helpful getting my payment mess resolved. We switched up cards, tried again, and it went through perfectly. She deserves some serious kudos. I've dealt with service people before who either couldn't be bothered or caved under the pressure of a crazy customer screw-up, but she handled it quite well.

I will definitely be returning in the future for more accessories and parts!

Camdon

View All Testimonials

Write Your Own Testimonial

FIC 2150cc Injector Set (High-Z) - EVO X

Product Description

Mitsubishi Evo X BlueMAX Fuel Injector Clinic Injector Set: 4 x 2150cc Saturated / High Impedance Injectors. Largest high impedance injector ever! Drop-in fit for size and plug! These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. These injectors do not require a resistor pack or P&H drivers. DO NOT USE WITH VP Import, Q16 or OTHER MTBE OXYGENATED FUELS

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set. Dynamic flow matching is used only on injector sets where the additional time and cost are justified by the corresponding benefits gained during the tuning process.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

The superior spray pattern and atomization make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

Fuel Injector Clinic injectors use the factory electrical connector or include solder-in pigtails. You can purchase adaptor ‘plug-n-play’ harnesses to avoid cutting your stock harness as an optional extra.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This massive injector is in a class of its own when low end throttle response and short pulse width control is required. Multi point dynamic flow matching is used during the production of these injector sets due their large flow rate which significantly improves the ECU’s ability to control these injectors in the sub 2ms pulse width area )typical of idle and part throttle conditions.)

The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please strictly follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)

Part# IS127-2150H

Details

Price: $879.95

Purchase Product