Home
Help
Testimonials
New Arrivals
View Cart
Install Tips
Categories
Air Intake
Accessories
Blow Off Valve
Boost Controllers
Brakes
Clutch - Trans
Electronics
Engine
Exhaust
Exterior
Fuel
Gauges
Intercooler
Interior
Maintenance
Suspension
Turbo
Wheels
Deals of the Day
Bestsellers
1.
Injen Cast Aluminum Intake System w/ Full Intercooler Piping Short Ram Intake- EVO 8/9
2.
Injen Short Ram Intake- 2008, 2010-2015 Mitsubishi EVO X
3.
K&N Replacement Air Filter - For EVO Injen Intake SP1898
4.
K&N High Flow Panel Air Filter - EVO X / Ralliart / GTS
5.
Cosworth High Flow Synthetic Air Filter - EVO X
6.
ETS Air Intake System - EVO X
7.
AEM Cold Air Intake Gun Metal Gray - Lancer Ralliart 2009+
8.
Buschur Racing Evolution Air Filter Kit - EVO 8/9
9.
ETS Air Intake System - EVO 8/9
10.
K&N Typhoon Short Ram Intake System Wrinkle Red - EVO X
Testimonials
Unbelievable!!! I love this place... I find myself looking for more parts right after I place an order! Shipping is always fast and customer service is always friendly. Thanks for all your hard work.
Avery Kunz
View All Testimonials
Write Your Own Testimonial
Recently Viewed
Mitsubishi OEM Rear Right Window Regulator - EVO X
Mitsubishi OEM Steering Column Signal Switch - Lancer 08+
GSC Manganese Bronze Exhaust Valve Guide Stopper Style- Set of 8 - EVO 8/9
Gift Cards
Gift certificates
TRENDING:
Rexpeed
|
AMS
|
Ultimate Racing
|
Engine Parts
|
Buschur Racing
LancerShop.com
::
Air Intake
:: BLE EVO Upgraded Lifter Set
BLE EVO Upgraded Lifter Set
BLE EVO Upgraded Lifter Set
Product Description
Our BLE Solid Lifters have specific enhancements over the factory and aftermarket hydraulic units. Only the finest 8620 Aerospace and 4130 chromoly steel is used to manufacture this product. Each assembly incorporates a fine-threaded lash adjuster, which features a radiused pivot head, built to exact OEM tolerances for use with the factory rocker arm. The lash adjuster is heat treated to increase surface hardness for maximum durability & wear resistance. It is locked in place to the lifter body using an 18-8 SS jam nut. The lifter body is cryogenically treated and its outside diameter is precision machined to match the cylinder head slot and oil passage clearances. Furthermore, the assembly is then chemically coated with black oxide for lubricity, corrosion protection, and improved wear & anti-galling characteristics.
The solid lifter conversion replaces the factory hydraulic lifters and comes with all necessary hardware for a straightforward installation. These Conversion Kits are perfect for anyone upgrading the factory valvetrain and/or camshafts in their sport compact
The main reason we designed this product is pure and simple... Horsepower. A solid lifter valvetrain is more consistent, opens to a greater extent, and closes faster than a hydraulic setup. This translates into better control of the valvetrain, as well as more duration spent at higher flow valve lifts. In essence, more high rpm power is found by eliminating the physical "collapse" (and resulting power loss) experienced by hydraulic lifters at certain rpm thresholds and valvespring pressure levels. The stronger your valve springs, the sooner this collapse will occur with hydraulics! Likewise, fluctuations in oil pressure will affect the operation of your hydraulic lifters, not so with this solid lifter conversion. As a result, the BLE Solid Lifters allow for higher spring pressures to be run, as well as, more aggressive camshaft lifts. So go ahead, REV IT UP!
In race applications, where the engine is operated for shorter durations, and undergoes closer inspection intervals, a simple "splash" lubricated rocker pivot is acceptable. However, for street & daily operation, where constant surveillance is both unlikely and cumbersome, a steady flow of oil to the rocker is highly recommended for obvious reasons. With that said, our Solid Lifters incorporate an oil feed with a restrictor to lube the rocker, while functioning similar to the "controlled" bleed of the OEM hydraulic units. Other solid units on the market, with unrestricted oil (passages) release the full pressure of the engine's oil system, which can effectively lower the oil pressure excessively.
Fits:
Mitsubishi Lancer Evolution 8, 9 4g63
TECH TIP:
This is a full set! The set includes new BLE lifters to completely replace all your stock lifters.
Part # MT00116
Details
Price: $341.95
Purchase Product
Qty
Out of stock
Notify me when this product becomes available
Related Options
Also Bought
Customers who bought this product also purchased
C-West Front Bumper - EVO 8/9
Carbotech Front and Rear Brake Lines - Evo X
Defi Red Racer 60mm Volt Gauge
Mitsubishi OEM Clutch Release Fork - EVO X
Customers Also Bought
Customers who bought this item also bought...
Zaklee Clear Cam Gear Cover - EVO 8
Mitsubishi OEM Exhaust Manifold to Head Gasket - EVO 8/9
Mitsubishi OEM Valve Cover Gasket - EVO 8
Fluidampr Harmonic Damper: EVO 8/9
Online Users
» 4313 Shoppers
Your cart
Welcome to LancerShop! In order to shop with us, you must
create an account
.
Your Cart is Empty!
»
View cart
»
Checkout
»
Wish list
»
Where's my stuff?
Your Account
Username
Password
Remember Me
Recover password
If Javascript is enabled in your browser click here
Help
»
Sales Inquiries
»
Contact us
»
Privacy statement
»
Recover password
Home
|
Tracking
|
Help
|
Install Tips
|
New Parts
|
Testimonials
|
Terms
1-888-554-6447 --
[email protected]
-- URL:
https://www.LancerShop.com
© 2002-2024 LancerShop.com. All Rights Reserved.